Geometry (All) Panel

At the object level, Relax applies to the entire object. At sub-object levels, Relax applies only to the current selection.

Note: To open the Relax Settings dialog, use the drop-down menu or +click the Relax button.

• Object, Polygon, and Element levels Lets you add polygons in the active viewport. After you turn on Create, click three or more times in succession anywhere, including on existing vertices, to define the shape of the new polygon. To finish, right-click.

  While creating a polygon at the Polygon or Element level, you can delete the most recently added vertex by pressing . You can do this repeatedly to remove added vertices in reverse order of placement.

  You can start creating polygons in any viewport, but all subsequent clicks must take place in the same viewport.

  Tip: For best results, click vertices in counterclockwise (preferred) or clockwise order. If you use clockwise order, the new polygon will face away from you.
• Vertex level Lets you add vertices to a single selected poly object. After selecting the object and clicking Create, click anywhere in space to add free-floating (isolated) vertices to the object. The new vertices are placed on the active construction plane unless object snapping is on. For example, with face snapping on, you can create vertices on object faces.
• Edge and Border levels Lets you create an edge between a pair of non-adjacent vertices on the same polygon. Click Create, click a vertex, and then move the mouse. A rubber-band line extends from the vertex to the mouse cursor. Click a second, non-adjacent vertex on the same polygon to connect them with an edge. Repeat, or, to exit, right-click in the viewport or click Create again.

  Edges you create separate the polygons. For example, by creating an edge inside a quadrilateral polygon, you turn it into two triangles.

You can attach any type of object, including splines, patch objects, and NURBS surfaces. Attaching a non-mesh object converts it to editable-poly format.

When you attach an object, the materials of the two objects are combined in the following way:

• If the object being attached does not have a material assigned, it inherits the material of the object it is being attached to.
  

  Handle inherits material from the cup it is being attached to.

• Likewise, if the object you're attaching to doesn't have a material, it inherits the material of the object being attached.
• If both objects have materials, the resulting new material is a multi/sub-object material that includes the input materials. A dialog appears offering three methods of combining the objects' materials and material IDs. For more information, see Attach Options Dialog.

  Attach remains active in all sub-object levels, but always applies to objects.

Upper left: Shaded view of model

Upper right: Wireframe view of model

Lower left: Model with objects attached

Lower right: Subsequent multi/sub-object material

Note: To attach objects from a list, use the drop-down menu or +click the Attach button.

Separates the selected sub–objects and associated polygons as a new object or element(s).

When you click Detach, the software prompts you for the options specified on the Detach dialog. If the object is in Edit Poly (modifier) format, you can detach using the current settings without opening the dialog by +clicking the Detach button.

Creates a single polygon from a vertex or edge selection and selects the polygon. Available at the Vertex, Edge, and Border sub-object levels only.

Select vertices or edges and then click Cap Poly.

Using Cap Poly with a vertex selection

Using Cap Poly with an edge selection

Using Cap Poly with a border selection

When capping an edge selection, the software uses the edge vertices to determine the feasibility of creating a polygon. When using Cap Poly at the Vertex or Edge level, the software requires a non-overlapping counter-clockwise sequence of selected sub-objects. Consider the example shown in the following illustration, in which the goal is to cap all border edges or vertices:

The software first determines the geometric center of the selected sub-objects (the small green disc), and then shoots out “rays” in counter-clockwise order from that location to find the locations of vertices from which to form a polygon. In this case, it finds vertex 6 before it finds vertex 7, but vertex 7 actually precedes vertex 6 when going around the border in counter-clockwise order. As a result, Cap Poly cannot form the polygon because the vertices it finds are in the wrong order.

In such cases, apply Cap Poly at the Border sub-object level.

A set of tools for converting triangles to quadrilaterals. Click the visible tool to apply it, or choose another tool from the drop-down list.

• Quadrify All Removes edges from the entire object to convert triangles to four-sided polygons.
• Quadrify Selection Removes edges from the current sub-object selection to convert triangles to four-sided polygons.
• Select Edges from All Selects edges that would be removed in a Quadrify All operation.

  To see the selection, go to the Edge sub-object level.

• Select Edges from Selection Selects edges that would be removed in a Quadrify All operation.

  To see the selection, go to the Edge sub-object level.

Creates a gizmo for a slice plane that you can position and rotate to specify where to slice. Also enables the Slice and Reset Plane buttons; click Slice to create new edges where the plane intersects the geometry.

If you use Slice Plane from the ribbon, the Slice, Split, and Reset Plane controls are available on the Slice Mode contextual panel.

If snapping is off, you see a preview of the slice as you transform the slice plane. To perform the slice, click the Slice button.