Service Pack 1 - for Autodesk Inventor View 2015 (Build 201)
September 11, 2014
Release Notes - Autodesk Inventor View 2015 SP1 Readme
Autodesk, Inc.
In a continuing effort to provide high quality products, this Service Pack 1 for Autodesk Inventor View 2015 fixes or addresses a
variety of issues. This file highlights how to install the service pack and what has been fixed.
General
- SP1(Build 201) installs on Autodesk Inventor View 2015(Build 153).
- Install only the Autodesk Inventor View 2015 Service Pack 1 that matches the bit-type; either 32-bit or 64-bit depending upon your operating system.
- When appending this Service Pack 1 to a deployment, it is recommended to update the deployment image on the same bit-type machine as the machine for the final installation from that image. For more information about Network Deployments, see the Network Administrator's Guide.
- Keep the original installation media or network image readily accessible during installation and uninstallation in case you are prompted for it.
- This Service Pack 1 includes all released hotfixes for Autodesk Inventor View 2015, including fixes made within OpenSSL, so no prerequisite installations are required.
Installation
- Update your operating system before you install Autodesk Inventor View 2015 Service Pack 1. Reboot
your system after the updates are installed.
- Download the appropriate version of Autodesk Inventor View 2015 Service Pack 1; either the 32-bit
or 64-bit version depending upon your operating system bit type.
- Double click the .msp file to update Autodesk Inventor View 2015 with Service Pack 1. A
progress bar displays while the installer updates the files on your system. When done, click Finish.
- If required, reboot the system after installation of the Service Pack 1 is finished.
To verify the success of the installation, start Autodesk Inventor View. On the Info Center Help drop-down list, select About Autodesk
Inventor View. If the About box displays: Build: 201, Release: 2015 SP1, the installation was successful.
Uninstallation
The installer process sometimes hangs as it waits for operating system file update time-outs. If
the following steps do not enable the process to complete, wait until all of these file updates complete. This
process takes up to 6 hours. To greatly speed up the uninstall process, perform the following steps:
- In your system Control Panel, access Network Connections.
- Disable the local area connection and all network adaptors, including virtual adaptors.
- After the uninstall process is completed successfully, in your system Control Panel, re-enable the local area connection and all network adaptors, including virtual adaptors.
- If required, reboot the system after the uninstallation of the Service Pack 1 is finished.
Sometimes hotfix icon cannot be uninstalled from the control panel, perform the following steps:
- Go to regedit.
- Find the key named Autodesk Inventor View 2015_[hotfix number] under Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall.
- Delete this key and all of its subkeys.
Return to Top
- Verify that you have administrator privileges on your local machine to install Autodesk Inventor View
2015 Service Pack 1.
- The 32-bit version of Autodesk Inventor View 2015 Service Pack 1 is approximately 30.8 MB in size. A
minimum of 0.50 GB of free disk space is required on the drive where your temporary files are directed.
- The 64-bit version of Autodesk Inventor View 2015 Service Pack 1 is approximately 52.8 MB in size. A
minimum of 1.00 GB of free disk space is required on the drive where your temporary files are directed.
Return to Top
Locate Autodesk Inventor View 2015 Service Pack 1 here: Inventor View Updates
Return to Top
Autodesk Inventor View, Autodesk Vault, Autodesk Data Management Server,
Autodesk Productstream, Autodesk Autoloader, AutoCAD, AutoCAD Mechanical, and AutoCAD Electrical, are trademarks or registered
trademarks of Autodesk, Inc. in the United States and/or other
countries.
Windows 7, Windows 8, Microsoft Word, and Microsoft Excel are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
Portions of this software copyright 1996-2008 Acresso Corporation.
All other trademarks are the property of their respective owners.
Return to Top
We thank all our customers who identified these issues and reported them to us. These reports give us the opportunity to improve the product and provide you with the best solution in mechanical design. We also thank you for your continued business and for the feedback regarding the content of this update release.
Respectfully,
Autodesk Inventor View Product Team
Return to Top
Copyright © 2014 Autodesk, Inc.